EXSYS EX-44016-L Manual de Instalação descarregar pdf

6 5

EXEXEX

-440164401644016

-LLL

EnglishEnglishEnglish

EXEXEX

-440164401644016

-LLL

EnglishEnglishEnglish

Die EX-44016-L ist eine LowProfile PCI-Express serielle RS-232 Karte mit 16 seriellen FIFO

16C95x Ports für den Anschluss von High-Speed seriellen RS-232 Peripherie Geräten (z.B.

Terminal, Modem, Plotter usw.). Der serielle PCI-Express Bus unterstützt dabei optimal die

Leistung des schnellen 16C95x Chipset mit 128byte FIFO Cache. Die EX-44016-L gewährleis-

tet so eine sichere Datenübertragung und exzellente Performance von bis zu 921KBaud/s für

jedes angeschlossene Gerät! Sie unterstützt alle PCI-Express Slots von x1 bis x16. Es ist nicht

möglich die I/O Adressen und Interrupts manuell einzustellen, da die Einstellungen der Karte

vom System (BIOS) und beim installieren des Betriebssystems automatisch vorgenommen

werden. Per Jumper können Sie 12V oder 5V auf Pin59 (GND) des seriellen Anschluss leiten.

Achten Sie bitte darauf dass die Angeschlossenen Geräte dies auch unterstützen! Bei der EX-

44016-L handelt es sich um eine LowProfile Karte mit 8cm Bügel für schmale Gehäuse.

BESCHREIBUNG & TECHNISCHE DATEN:

AUFBAU:

Kompatibilität: PCI Express x1 bis x16

Betriebs Systeme: Windows 2000/ Server 2003 & 2008/ XP/ Vista/ 7/ Linux

Anschlüsse: 16x 9 Pin Seriell D-Sub Stecker

Lieferumfang: EX-44016-L, Treiber CD, Anleitung, Octopus Kabel

Zertifikate:

CECE

CE / FCC / RoHS / WEEE DE97424562 / WHQL

For aux power (JP3) J7 must be connected to pc power supply !

If not, the card wont work.

JUMPER SETTING & CONNECTORS:

DB 9M:

Pin Signal Pin Signal Pin Signal

1 CDC 4 DTR 7 RTS

2 RXD 5 GROUND 8 CTS

3 TXD 6 DSR 9 RI

Serial 9 Pin D-SUB connector

J3:

JUMPER EINSTELLUNG & ANSCHLÜSSE:

JP1 & JP2:

BedienungsanleitungBedienungsanleitung

Vers. 1.0 / 01.03.12

JP3:

X 5V = 5Volt vom PC-Netzteil auf GND (Pin59)

X 12V = 12Volt vom PC-Netzteil auf GND (Pin59)

I 12V = 12Volt vom Mainboard (STANDARD)

X5V

X12V

I12V

DIS = Am Pin 59 liegt das Standard Signal an (GND).

(Werkseinstellung)

PWR = PWR (POWER) = Achtung! Jumper nicht

auf diese Einstellung setzen! Karte, PC & Endgeräte

könnten beschädigt werden! Strom auf GND!!!

Die Einstellung der Spannung nehmen Sie mit JP3 vor. Dieser sollte

aber bei Standard Anwendungen nicht verstellt werden!

DRIVER INSTALLATION:

Windows 2000/ XP/ Vista/ 7:

After starting Windows it recognizes a new “PCI Controller“ and opens the hardware assis-

tant. Please choose manual installation and put the driver CD into your CD-ROM drive. Now

enter the Path "D:\IO\OXFORD2\" and then the directory of your operating system into the box

for the Path/Source and click at >next/continue<. Now Windows searches for the drivers in

the specified directory. Follow the hardware assistant and finish the installation. If Windows

recognizes other new devices repeat the above described steps.

Attention! Restart your PC in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows that

opens select >Device Manager<. Under „Ports (COM and LPT)“ you should find a new „PCI

Port“ as sample (COM3). If you see this or similar entries the card is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM3 to COM5, open the >Device Manager<

click at >COM3<, >Settings< and then >Advance<. There you can change between COM3 till

COM256. The LPT Ports can be changed in the same way!

Windows Server 2000/ 2003/ 2008:

After starting Windows it recognizes a new “PCI Controller“ and opens the hardware assis-

tant. Please choose manual installation and put the driver CD into your CD-Rom drive. Now

enter the Path "D:\IO\OXFORD2\" and then the directory of your operating system for Server

2000: “2000“, for Server 2003: “XP32“ or “XP64“, for Server 2008: „Vista32“ or „Vista64“ and

for Server 2008 R2: „Win7_32bit“ or Win7_64bit“ into the box for the Path/Source and click at

>next/continue<. Now Windows searches for the drivers in the specified directory. Follow the

hardware assistant and finish the installation. If Windows recognizes other new devices repeat

the above described steps.

Attention! Restart your PC in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows that

opens select >Device Manager<. Under „Ports (COM and LPT)“ you should find a new „PCI

Port“ as sample (COM3). If you see this or similar entries the card is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM3 to COM5, open the >Device Manager<

click at >COM3<, >Settings< and then >Advance<. There you can change between COM3 till

COM256. The LPT Ports can be changed in the same way!

LINUX:

The drivers are located in the following folder on our driver CD:

"D:\IO\OXFORD2\LINUX"

Because each individual distribution and kernel version of Linux is different, sadly we cant

provide a installation instruction. Please refer to the installation manual for standard I/O ports

from your Linux version! In some newer versions of Linux the card will even be installed auto-

matically after starting Linux.

If you are ready with the jumper settings, please proceed with the following installation instructions.

Because there are large differences between PC’s, we can give you only a general installation

guide for the EX-44016-L. Please refer to your computer’s reference manual whenever in doubt.

1. Turn off the power to your computer and any other connected peripherals.

2. Remove the mounting screws located at the rear and/ or sides panels of your Computer and

gently slide the cover off.

3. Locate an available expansion slot and remove its covers from the rear panel of your com-

puter. Make sure it is the right expansion slot for the card (see card description)

4. Align the card with the expansion slot, and then gently but firmly, insert the card. Make sure

the card is seated and oriented correctly. Never insert the card by force!

5. Then connect the card with a screw to the rear panel of the computer case.

6. Gently replace your computer’s cover and the mounting screws.

HARDWARE INSTALLATION:

DIS | PWR

(Nur in Verbindung mit speziellem Kabel & JP1 auf PWR!!!)

Für Strom vom Netzteil muss J3 mit PC Netzteil verbunden werden!

Pin Signal Pin Signal Pin Signal

1 DCD 1 24 DSR 3 47 RTS 6

2 RXD 1 25 RTS 3 48 CTS 6

3 TXD 1 26 CTS 3 49 GND

68 Pin mini half pitch connector

4 DTR 1 27 DCD 4 50 DCD 7

5 DSR 1 28 RXD 4 51 CN_PWR

6 RTS 1 29 TXD 4 52 CN_PWR

7 CTS 1 30 DTR 4 53 RXD 7

8 DCD 2 31 DSR 4 54 GND

9 RXD 2 32 RTS 4 55 TXD 7

10 TXD 2 33 CTS 4 56 GND

11 DTR 2 34 NC 57 DTR 7

12 DSR 2 35 DCD 5 58 DSR 7

13 RTS 2 36 RXD 5 59 RTS 7

14 CTS 2 37 TXD 5 60 CTS 7

15 GND 38 DTR 5 61 DCD 8

16 DCD 3 39 DSR 5 62 RXD 8

17 CN_PWR 40 RTS 5 63 TXD 8

18 CN_PWR 41 CTS 5 64 DTR 8

19 RXD 3 42 DCD 6 65 DSR 8

20 GND 43 RXD 6 66 RTS 8

21 TXD 3 44 TXD 6 67 CTS 8

22 GND 45 DTR 6 68 NC

23 DTR 3 46 DSR 6

HPC68F:

S1-S16: 68 Pin Stecker zu

16 x 9 Pin Serieller Anschluss

JP1&2: Power auf 9 Pin

Stecker Ein/Aus

JP3: Jumper für die

Stromquelle

(Netzteil- oder

PCI-Express Bus)

J3: Anschluss für

Strom vom PC

Netzteil

Serielle Chip 16C950

1 +5V

2 GND

3 GND

4 +12V

1 2

Resumo do Conteúdo

Página 1 - Windows 2000/ XP/ Vista/ 7:

6 5 EXEXEX---440164401644016---LLL EnglishEnglishEnglish EXEXEX---440164401644016---LLL EnglishEnglishEnglish 1 Die EX-44016-L ist eine LowP

Página 2 - User ManualUser Manual

2 3 4 EXEXEX---440164401644016---LLL DeutschDeutschDeutsch EXEXEX---440164401644016---LLL DeutschDeutschDeutsch The EX-44016-L is a plug &a

Comentários a estes Manuais

Sem comentários

EXSYS EX-44016-L Manual de Instalação

Consulte online ou descarregue Manual de Instalação para Placas/adaptadores de interface EXSYS EX-44016-L. EXSYS EX-44016-L Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Placas/adaptadores de interface EXSYS EX-44016-L