EXSYS EX-44272 Manual de Instalação descarregar pdf (Página 1)

If you are ready with the jumper settings, please proceed with the following installation

instructions. Because the designs of computers are different, only general installation

instructions are given. Please refer your computer’s reference manual whenever in doubt.

1. Turn off the power to your computer and any other connected peripherals.

2. Remove the mounting screws located at the rear and/or sides panels of your Comput-

er and gently slide the cover off.

3. Locate an available expansion slot and remove its covers from the rear panel of your

computer. Make sure it is the right expansion slot for the card (see card description)

4. Align the card with the expansion slot, and then gently but firmly, insert the card.

Make sure the card is seated and oriented correctly. Never insert the card by force!

5. Then connect the card with a screw to the rear panel of the computer case.

6. Gently replace your computer’s cover and the mounting screws.

HARDWARE INSTALLATION :

6 5

EXEXEX

-44072 / EX44072 / EX44072 / EX

-442724427244272

EnglishEnglishEnglish

EXEXEX

-44072 / EX44072 / EX44072 / EX

-442724427244272

EnglishEnglishEnglish

Die EX-44072/EX-44272 ist eine PCI-Express serielle RS-232 Karte mit 2 seriellen FIFO

16C95x Ports, für den Anschluss von High-Speed seriellen RS-232 Peripherie Geräten (z.B.

Terminal, Modem, Plotter usw.). Der serielle PCI-Express Bus unterstützt dabei optimal die

Leistung des schnellen 16C95x Chip-Set mit 128byte FIFO Cache. Die EX-44072 gewährleis-

tet so eine sichere Datenübertragung und exzellente Performance von bis zu 921KBaud/s für

jedes angeschlossene Gerät! Sie unterstützt alle PCI-Express Slots von x1 bis x16. Es ist nicht

möglich die I/O Adressen und Interrupts manuell einzustellen, da die Einstellungen der Karte

vom System (BIOS) und beim Installieren des Betriebssystems automatisch vorgenommen

werden. Mit dem Jumper JP2 & JP3 können Sie 12V oder 5V auf Pin 9 des seriellen Anschlus-

ses leiten. Achten Sie bitte darauf dass die Angeschlossenen Geräte dies auch unterstützen.

Die EX-44272 ist eine LowProfile Karte für schmale PC Gehäuse bis 8cm Bauhöhe.

BESCHREIBUNG & TECHNISCHE DATEN :

AUFBAU :

Kompatibilität: PCI Express x1 bis x16

Betriebs Systeme: WIN 2000/XP/Vista/Server 2000/2003/2008/Win7, Linux

Anschlüsse: 2 x 9 Pin Sub-D Stecker

Lieferumfang: EX-44072 oder EX-44272, Treiber CD, Anleitung

Zertifikate:

CECE

/ FCC / RoHS / WEEE DE97424562 / WHQL

DRIVER INSTALLATION :

For aux power (JP2) J6 must be connected to pc power supply !

If not, the card wont work.

JUMPER SETTING & CONNECTORS:

DB 9M:

Pin Signal Pin Signal Pin Signal

1 CDC 4 DTR 7 RTS

2 RXD 5 GROUND 8 CTS

3 TXD 6 DSR 9 RI

Serial 9 Pin D-SUB connector:

1 +5V

2 GND

3 GND

4 +12V

J6:

JUMPER EINSTELLUNG & ANSCHLÜSSE:

S1 9 Pin Stecker

Serieller Anschluss

JP3 Power auf 9 Pin Stecker Ein/Aus

S1 Interner Serieller

Anschluss

JP2 Jumper für die Strom-

quelle (Netzteil oder

PCI-Express Bus)

J6 Anschluss für Power

vom PC Netzteil

Windows 2000/XP/Vista & 7:

After starting Windows it recognizes a new “PCI Controller“ and opens the hardware

assistant. Please choose manual installation and put the driver CD into your CD-Rom

drive. Now enter the Path "D:\IO\OXFORD2\" and then the directory of your operating

system “2000“ “XP32“ “XP64“ “Vista32“ “Vista64“ “Win7_32bit“ or “Win7_64bit“

into the box for the Path/Source and click at >next/continue<. Now Windows search

for the drivers in the specified directory. Follow the hardware assistant and finish the

installation. If Windows recognizes other new devices repeat the above described

steps. Attention! Restart Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows

that open select >Device Manager<. Under ”Ports (COM and LPT)“ you should find

one or more new ”PCI Ports“ as sample (LPT2) or (Com3). If you see this or similar

entries the card is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM 3 to COM5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can change

between COM 3 till 256.

Windows Server 200x:

After starting Windows it recognizes a new “PCI Controller“ and opens the hardware

assistant. Please choose manual installation and put the driver CD into your CD-Rom

drive. Now enter the Path "D:\IO\OXFORD2\" and then the directory of your operating

system for Server 2000: “2000“ for Server 2003: “XP32“ or “XP64“ and for Server

2008: “VISTA32“ or “VISTA64“ into the box for the Path/Source and click at >next/

continue<. Now Windows search for the drivers in the specified directory. Follow the

hardware assistant and finish the installation. If Windows recognizes other new devices

repeat the above described steps. Attention! Restart Windows in any case after in-

stalling the drivers.

CHECK THE INSTALLED DRIVER:

Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows

that open select >Device Manager<. Under "Ports (COM and LPT)“ you should find

one or more new ”PCI Ports“ as sample (LPT2) or (Com3). If you see this or similar

entries the card is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM 3 to COM5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can change

between COM 3 till 256.

LINUX:

There are no drivers available for Linux, but the card is supported by the most versions

of Linux. Because each individual distribution and kernel version of Linux is different,

sadly we cant provide a installation instruction. Please refer to the installation manual

for standard IO ports from your Linux version! In some newer versions the card will

even be installed automatically after starting Linux.

BedienungsanleitungBedienungsanleitung

Vers. 1.3 / 05.12.11

S2 9 Pin Stecker

Serieller Anschluss

JP2:

Wenn sie den Jumper JP3 für S1 bis S2 auf PWR gesetzt haben, kön-

nen sie mit dem JP2 den Spannungswert einstellen. Es gibt 3 verschie-

dene Spannungsquellen. (Nur in Verbindung mit JP3 auf PWR!!!)

X 5V = 5Volt vom PC-Netzteil

X 12V = 12Volt vom PC-Netzteil

I 12V = 12Volt vom Mainboard (STANDARD)

X5V

X12V

I12V

JP3:

DIS = Am Pin 9 liegt das Standard Signal RI (Ring Indicator).

(Werkseinstellung)

PWR = Am Pin 9 kann jetzt eine Spannung von DC5V oder DC12V

eingestellt werden.

Die Einstellung der Spannung nehmen sie mit JP2 vor. Dieser sollte

aber bei Standard Anwendungen nicht verstellt werden.

DIS PWR

1 2

Resumo do Conteúdo

Página 1 - Vers. 1.3 / 05.12.11

If you are ready with the jumper settings, please proceed with the following installation instructions. Because the designs of computers are d

Página 2 - User ManualUser Manual

2 3 4 EXEXEX---44072 / EX44072 / EX44072 / EX---442724427244272 DeutschDeutschDeutsch EXEXEX---44072 / EX44072 / EX44072 / EX---442724427244272

Comentários a estes Manuais

Sem comentários

EXSYS EX-44272 Manual de Instalação Página 1

Consulte online ou descarregue Manual de Instalação para Placas/adaptadores de interface EXSYS EX-44272. EXSYS EX-44272 Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

EXSYS EX-44272 Manual de Instalação Página 1

Consulte online ou descarregue Manual de Instalação para Placas/adaptadores de interface EXSYS EX-44272. EXSYS EX-44272 Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Placas/adaptadores de interface EXSYS EX-44272