EXSYS EX-44392 Manual de Instalação descarregar pdf (Página 1)

If you are ready with the jumper settings, please proceed with the following installation

instructions. Because the designs of computers are different, only general installation

instructions are given. Please refer your computer’s reference manual whenever in doubt.

1. Turn off the power to your computer and any other connected peripherals.

2. Remove the mounting screws located at the rear and/or sides panels of your Com-

puter and gently slide the cover off.

3. Locate an available expansion slot and remove its covers from the rear panel of your

computer. Make sure it is the right expansion slot for the card (see card description)

4. Align the card with the expansion slot, and then gently but firmly, insert the card.

Make sure the card is seated and oriented correctly. Never insert the card by force!

5. Then connect the card with a screw to the rear panel of the computer case.

6. Gently replace your computer’s cover and the mounting screws.

HARDWARE INSTALLATION :

6 5

44392

English

44392

English

Die EX-44390 ist eine PCI-Express Multi I/O Karte mit 2 seriellen FIFO 16C95x Ports,

für den Anschluss von High-Speed seriellen RS-232 Peripherie Geräten (z.B. Terminal,

Modem, Plotter usw.). Der serielle PCI-Express Bus unterstützt dabei optimal die Leis-

tung des schnellen 16C95x Chipsets mit 128byte FIFO Cache. Die EX-44390 gewähr-

leistet so eine sichere Datenübertragung und exzellente Performance von bis zu

921KBaud/s für jedes angeschlossene Gerät! Sie unterstützt alle PCI-Express Slots

von x1 bis x16. Es ist nicht möglich die I/O Adressen und Interrupts manuell einzustel-

len, da die Einstellungen der Karte vom System (BIOS) und beim Installieren des Be-

triebssystems automatisch vorgenommen werden.

BESCHREIBUNG & TECHNISCHE DATEN :

AUFBAU :

DRIVER INSTALLATION :

JUMPER SETTING & CONNECTORS:

JUMPER EINSTELLUNG & ANSCHLÜSSE:

CHECK THE INSTALLED DRIVER:

Click at >Start< >Run< then enter “compmgmt.msc“ and click at >OK<. In the win-

dows that opens select >Device Manager<. Under „Ports (COM and LPT)“ you

should find a new „PCI Port“ as sample (Com3). If you see this or similar entries the

card is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM 3 to COM5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can change

between COM 3 till 256.

Windows Server 200x:

After starting Windows it recognizes a new “PCI Controller“ and opens the hardware

assistant. Please choose manual installation and put the driver CD into your CD-Rom

drive. Now enter the Path "D:\IO\OXFORD\" and then the directory of your operating

system for Server 2000: “2000“, for Server 2003: “XP32“ or “XP64“, for den Server

2008: „Vista32“ or „Vista64“ and for the Server 2008 R2: „Win7_32bit“ or Win7_64bit“

into the box for the Path/Source and click at >next/continue<. Now Windows searches

for the drivers in the specified directory. Follow the hardware assistant and finish the

installation. If Windows recognizes other new devices repeat the above described

steps. Attention! Restart Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at >Start< >Run< then enter “compmgmt.msc“ and click at >OK<. In the win-

dows that opens select >Device Manager<. Under „Ports (COM and LPT)“ you

should find a new „PCI Port“ as sample (Com3). If you see this or similar entries the

card is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM 3 to COM5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can change

between COM 3 till 256. The LPT Ports can be changed in the same way!

Windows NT 4.0:

Start Windows NT and insert the driver CD into your CD-ROM drive (for example D:).

Click at >Start< >Run< and enter „D:\IO\OXFORD\NT4\Install_Serial.exe" then click

>OK<. Windows NT will now start the setup program and install the driver. Please

Restart Windows NT after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at >Start< >Programs< >Administrative Tools[Common]< >Windows NT-

Diagnostics< then click at >Resource< >IRQ<. Here you should find the entry „09

oxser 0 PCI“. Then click at >I/O-Port< here you should see the entries „D400-D407

oxser 0 PCI“ „D800-D802 oxser 0 PCI“ and „DC00-DC1F oxser 0 PCI“

for the ports. The I/O addresses can change depends which system and card is in-

stalled. If you see these or similar entry's the card is installed correctly.

LINUX:

There are no drivers available for Linux, but the card is supported by the most versions

of Linux. Because each individual distribution and kernel version of Linux is different,

sadly we cant provide a installation instruction. Please refer to the installation manual

for standard IO ports from your Linux version! In some newer versions the card will

even be installed automatically after starting Linux.

Bedienungsanleitung

Vers. 1.0 / 14.12.10

Kompatibilität: PCI-Express x1 bis x16

Betriebs Systeme: WIN 9x/ME/NT4/2000/XP/Server 2003/Vista/7(Linux vom OS)

Anschlüsse: 2 x 9 Pin Sub-D Stecker

Lieferumfang: EX-44392, CD, Anleitung, Octopus Kabel mit 2 x 9 Pin Stecker

LowProfile Bügel

Zertifikate: CE / FCC / RoHS / WEEE DE97424562 / WHQL

DB9M:

Pin Signal Pin Signal Pin Signal

1 CDC 4 DTR 7 RTS

2 RXD 5 GROUND 8 CTS

3 TXD 6 DSR 9 RI

Serial 9 Pin D-SUB connector male :

1 +5V

2 GND

3 GND

4 +12V

J7:

Oxford

OXmPCI952 Chipset

JP1: Parallel Port

Ein/Ausschalten

Bitte nicht

verändern

J7: Anschluss für

PC-Netzteil

J8: 44 Pin D-Sub Buchse

mit Octopus Kabel

für die Anschlüsse S1 + S2

J2+ 10 Pin interner

J3 Serieller Anschluss

Jumper zum einstellen des Parallel Ports.

DIS = Der parallel Port ist a/jointfilesconvert/241335/bgeschaltet (Werkseinstellung).

ENA = Der Parallel Port ist Eingeschaltet.

Achtung: Bitte nicht veränder. Wird nur für die Karte EX-44390 benötigt

JP1:

DIS

ENA

DIS PWR

JP2:

DIS = Am Pin 9 liegt das Standard Signal RI (Ring Indicator).

(Werkseinstellung)

PWR = Am Pin 9 kann jetzt eine Spannung von DC5V oder

DC12V eingestellt werden.

Die Einstellung der Spannung nehmen sie mit JP3 vor. Dies sollte aber

bei Standard Anwendungen nicht verstellt werden.

JP3:

Wenn sie den Jumper JP2 für S1 und S2 auf PWR gesetzt haben,

können sie jetzt mit dem JP3 den Spannungswert einstellen. Es gibt 3

verschiedene Spannungsquellen. (Nur in Verbindung mit JP2 auf PWR!)

AUX 5V = 5Volt vom PC-Netzteil

AUX 12V = 12Volt vom PC-Netzteil

PCI 12V = 12Volt vom Mainboard (STANDARD)

AUX5V

AUX12V

PCI12V

For power over pc, power supply must be connected to J7!

JP2 Power auf 9 Pin Stecker

ein- oder ausschalten

JP3 Jumper für die Strom-

quelle (Netzteil oder

PCI-Express Bus)

DB 44F:

DRIVER INSTALLATION :

Windows 9x/ME/2000/XP/Vista & 7:

After starting Windows it recognizes a new “PCI Controller“ and opens the hardware

assistant. Please choose manual installation and put the driver CD into your CD-Rom

drive. Now enter the Path "D:\IO\OXFORD\" and then the directory of your operating

system into the box for the Path/Source and click at >next/continue<. Now Windows

searches for the drivers in the specified directory. Follow the hardware assistant and

finish the installation. If Windows recognizes other new devices repeat the above de-

scribed steps. Attention! Restart Windows in any case after installing the drivers.

1 2

Bedienungsanleitung 1
User Manual 2

Resumo do Conteúdo

Página 1 - Bedienungsanleitung

If you are ready with the jumper settings, please proceed with the following installation instructions. Because the designs of computers are different

Página 2 - User Manual

2 3 4 EXEXEX---443924439244392 DeutschDeutschDeutsch EXEXEX---443924439244392 DeutschDeutschDeutsch The EX-44392 is a plug & play high-spe

Comentários a estes Manuais

Sem comentários

EXSYS EX-44392 Manual de Instalação Página 1

Consulte online ou descarregue Manual de Instalação para Placas/adaptadores de interface EXSYS EX-44392. EXSYS EX-44392 Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

EXSYS EX-44392 Manual de Instalação Página 1

Consulte online ou descarregue Manual de Instalação para Placas/adaptadores de interface EXSYS EX-44392. EXSYS EX-44392 Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Placas/adaptadores de interface EXSYS EX-44392